Brand:
GESTERItem NO.:
GT-C12AOrder(MOQ):
1Payment:
T/T, L/CShipping Port:
China PortLead Time：
10-30 daysProduct Detail
Hydraulic Bursting Strength Tester GT-C12A
Application:
Hydraulic Bursting Strength Tester is applied to determine the bursting strength test and distension at burst of woven, knitted and non woven fabrics, papers and boards by the application of hydraulic load under a rubber diaphragm.
Standards:
ISO 13938.1, FZ/T 60019, FZ/T 01030, ASTM D3786, BS 4768, WOOLMARK TM 29WSP 30.1, JIS L 1018.6.17, SATRA TM170
|
Model |
GT-C12A-1 |
GT-C12A-2 |
|
Range |
2.00Mpa |
10.000Mpa |
|
The min. Division value |
0.001Mpa |
0.003Mpa |
|
Test area |
7.3 cm2 (Φ30.5mm), 10 cm2 (Φ35.7mm),
50cm2 (Φ79.8mm), 100 cm2 (Φ112.8mm) can be option |
|
|
Thickness of rubber diaphragm |
≤2mm |
|
|
Pressure speed |
100ml/min - 500ml/min |
|
|
Accuracy |
±1 mm, when the height at burst up to 70 mm |
|
|
Testing units |
Kpa, kgf/ cm2, atm, mmHg, lb/in2 free shift |
|
|
Test method |
Constant Rate Bursting,
Constant Expansion,
Constant Pressure,
Constant Time Bursting |
|
|
Output |
Printer ,display output, and can be connected to the computer |
|
|
Power supply |
AC 220V 50/60HZ 500W |
|
|
Dimensions |
550×450×700mm |
|
|
Net weight |
125kg |
|
|
Standard accessories |
1 set |
Test set of 7.3cm²(φ30.5mm) |
|
1 set |
Test set of 50cm²(φ79.8mm) |
|
|
1pc |
Wrench |
|
|
1pc |
Stainless steel calibration plate |
|
|
1pc |
Rubber diaphragm |
|
|
1pc |
English operation software |
|
|
1pc |
Cable connect with PC |
|
|
Optional accessories |
Optional |
Other test set |
|
Optional |
Rubber diaphragm |
|
|
Optional |
Air compressor |
Looking for a clean, oil-free option for standard textile testing?
Check out the Pneumatic Bursting Strength Tester GT-C12B (up to 1.5 MPa, compliant with ISO 13938-2).
Q1: What is the main difference between ISO 13938-1 (GT-C12A) and ISO 13938-2 (GT-C12B)?
A: The primary difference lies in the pressure medium and pressure limit. ISO 13938-1 specifies a hydraulic method (used in GT-C12A), which uses liquid under a diaphragm to reach higher pressures up to 10 MPa for heavy-duty materials. ISO 13938-2 specifies a pneumatic method (used in GT-C12B Pneumatic Bursting Tester), using compressed air up to 1.5 MPa for clean and rapid testing of standard textiles.
Q2: What test areas come standard with the GT-C12A?
A: The GT-C12A includes standard test sets for 7.3 cm² (Φ30.5 mm) and 50 cm² (Φ79.8 mm). Optional test adapters for 10 cm² and 100 cm² are also available to cover all international standard configurations.
Q3: Can the GT-C12A perform constant pressure or constant expansion tests?
A: Yes. Driven by an AC servo system, the GT-C12A features 4 programmable test modes: Constant Rate Bursting, Constant Expansion, Constant Pressure, and Constant Time Bursting, giving research laboratories total flexibility.
All kinds of below materials can be tested on the Bursting Strength Tester GT-C12
Friendly Links :
English 
