products categories


Download Download file and products catalogue for lab testing equipment, including including Footwear Testing Equipment and Textile Testing Equipment and Toys Testing Equipment and Furniture Testing Equipment.

contact us

  • If you have questions, please contact us, all questions will be answered
  • Tel : +86-595-22515230
  • Fax : +86-595-22515221
  • Email :

hot products

  • Three Pronged Clamp

    Three Pronged Clamp GT-M37

  •  Flammability Test

    Horizontal and Vertical Flame Chamber GT-MC35F-2

  • DIN Abrasion Tester

    DIN Abrader Rubber DIN Abrasion Tester GT-KB03

TPP Thermal Protection Tester GT-CN08
TPP Thermal Protection Tester GT-CN08
  • Brand:

  • Item No.:

  • Certificate:

    ISO 9001, UKAS, CE
  • Standard:

    NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.
  • Shipping Port:

    Xiamen Pport
  • Lead Time:

    About 25days
  • Payment:

contact now

TPP Thermal Protection Tester GT-CN08

Product Introduction


The TPP thermal protection instrument is mainly used to measure the thermal insulation performance of flame-retardant protective clothing fabrics exposed to radiant heat sources and convection heat sources to detect the thermal protection performance of protective clothing, safety shoes, gloves, and helmet outer surfaces.


  • The test equipment shall include the sample holder assembly, the holder of the sample holder assembly, the heat source, the protective cover, the sensor assembly, the recorder, and the gasket. It shall also have a gas source, a gas flow meter, a burner, and a sensor.
  • Removable corundum protection board, temperature 1800 degrees, can block the flame and reduce the test error.
  • Two 45-degree Meker burners were placed to provide standard convection heat sources with nine quartz tubes.
  • Meker burner diameter 38mm, internal hole diameter 5/16 inches, can provide 800-1200 BUT heat output, the burner mouth is a metal mesh structure, the burner lower air valve can be adjusted, adjustable air and flammable gas mixture proportion.
  • Nine T150 quartz IR arrays provide thermal radiation flux of 13-40 kW/m2 ± 4 kW/m2.
  • The total heat flux can be set to 83 kW/m2 ± 2 kW/m2 by adjusting the gas supplied to the Meker burner under the heat radiation of a quartz infrared tube.
  • The calibration heat flow meter is water-cooled, with a working range of 0-100 kW/m2 and a maximum range of 150%.
  • The response time of the heat flow meter is less than 200ms, the emissivity is greater than 0.95, and the output signal is greater than 5mv in the operating range.
  • The copper pan calorimeter device can be used to detect convective heat and radiant heat, while detecting the temperature of the back of the specimen.
  • The rotameter can adjust the flow of combustion gas with an accuracy of ±2% and a range of more than 3L/min.
  • The pointer pressure gauge, the inlet pressure can be adjusted through the pressure reducing valve, the pressure relief valve has a range of 0-15psi.
  • A quarter turn plug can manually shut off the flammable gas.
  • The temperature acquisition system has a resolution of 0.1C° and an accuracy of ±0.75°C.
  • The data acquisition speed of the automated data acquisition system is sub-/0.05 second and cold junction compensation is provided for thermocouple measurement data.
  • Equipped with computers and printers, comes with standard test software and provides standard test curves.

Key Specifications




Climate Requirements

Propane and compressor air

Test Environment


Holding Way

Pneumatic or manual

Power Supply

220V 50Hz 15A


1500×540×460mm ((W×H×D)




NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.

inquiry now

    We will give you a quotation within 24 hours.

      TPP Thermal Protection Tester GT-CN08

    Contact Us:

    Gester Instruments Co.,Ltd.

main Products
  • Nonwovens Strength Tester Nonwovens Strength Tester GT-CN01

    Nonwovens Strength Tester can be used to test nonwovens absorption, adhesive lining, multilayer laminated fabrics, hot melt adhesive lining, and between lining apparel fabrics, linings and fabrics, and coating adhesions various tensile and peel strength.

  • Absorption Tester Nonwovens Absorption Tester GT-CN02

    This Nonwovens Absorption Tester GT-CN02 is used to test absorption of nonwoven, such as liquid absorbency time, liquid absorptive capacity, liquid wicking rate, liquid wicking height.

  • Nonwovens Tester Nonwovens Run-off Tester GT-CN03

    This Nonwovens Run-off Tester GT-CN03 is used to test the overflow quantity of thin nonwoven, such as sanitary towel and diaper coating material.

  • Liquid Strike Through Time Tester Liquid Strike-Through Tester GT-CN04

    Liquid Strike-through tester can be used to determine the liquid strike-through test of nonwovens such as sanitary napkins, diaper covering materials and so on.